Search found 1036 matches

by curt
Fri Dec 30, 2022 10:03 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

That is one hella beefy duty notcher ya got there Curt. I like Baliegh tn250 super ridgid can cut offset and on a bend and over 180 degrees great for roll cages stupid nice for most all bike stuff but a pain to get setup going back to an even cut from an offset . i added a bolt to help and it would...
by curt
Fri Dec 30, 2022 12:59 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

ya sucks but learned the hard way what i was doing wrong and ill keep the pieces and make something else out of them
by curt
Thu Dec 29, 2022 4:40 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0213.JPG SANY0214.JPG SANY0215.JPG made three stupid mistakes today apparently i dont learn . first 2 i screwed the rotation on the final bend then on the replacement i put the bend on the wrong side of the line so now the 25 degree angle is to short to hit the axl in the right spot . :angry-ba...
by curt
Tue Dec 27, 2022 10:36 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

it is dan it was easier quittin smokin
by curt
Mon Dec 26, 2022 5:27 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0211.JPG
SANY0211.JPG (360.31 KiB) Viewed 4019 times
SANY0209.JPG
SANY0209.JPG (228.91 KiB) Viewed 4019 times
SANY0210.JPG
SANY0210.JPG (225.09 KiB) Viewed 4019 times
you know your having fun when you keep takin 1/16 at a time to get everything all even from side to side i love that notcher
by curt
Fri Dec 23, 2022 11:39 am
Forum: Project Build-Logs
Topic: The Unholy Virgin...Reincarnate
Replies: 109
Views: 40427

Re: The Unholy Virgin...Reincarnate

i like the brass ones better too
by curt
Thu Dec 22, 2022 5:55 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

i will maz . SANY0204.JPG SANY0205.JPG SANY0207.JPG had a little time today bent up the lower rails to the backbone . im not going to bend the rails up to the rear till i get the notches finalized to the backbone so that will be a little while . i never made one that went to the backbone before 3 tu...
by curt
Mon Dec 19, 2022 9:48 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

thank you
by curt
Sun Dec 18, 2022 6:44 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0202.JPG
SANY0202.JPG (386.01 KiB) Viewed 5967 times
got my garage back had some time to clean the notches and a little tack welding . got to work on the seat post tube so i can lock it in and start the bottom tubes
by curt
Mon Dec 12, 2022 4:55 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0199.JPG SANY0198.JPG its good to be back at it but i been stuck working on the daily . took a week to get the timing chains and tensioners should have the torque to yield crank and jackshaft bolt tomorrow . what is it with having to wait for everything anymore and not just a day or so but a we...
by curt
Thu Dec 01, 2022 8:42 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0196.JPG
SANY0196.JPG (344.79 KiB) Viewed 6029 times
SANY0197.JPG
SANY0197.JPG (344.71 KiB) Viewed 6029 times
got the bender setup and bending today notched out the wishbones took about 6 tries and a used hole saw to get them perfect . tomorrow i plan to clean up the notches and tube to tack everything together
by curt
Wed Nov 30, 2022 10:31 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0195.JPG
SANY0195.JPG (315.19 KiB) Viewed 6033 times
tube showed up so i spent some time putting the 17 degree bevel on the motor and trans mounts . slow going with a rotary file and drill press but should be a nice tight fit
by curt
Mon Nov 28, 2022 4:37 pm
Forum: The Bull Pen
Topic: shop talk by dennis kirk with bitter end old school chop
Replies: 2
Views: 2081

shop talk by dennis kirk with bitter end old school chop

https://youtu.be/_m1J5P4LhoM saw this the other day watch from the 47 min mark
by curt
Sun Nov 27, 2022 10:27 pm
Forum: Project Build-Logs
Topic: The Unholy Virgin...Reincarnate
Replies: 109
Views: 40427

Re: The Unholy Virgin...Reincarnate

cool
by curt
Sat Nov 26, 2022 7:10 pm
Forum: Frame Fabrication
Topic: new project
Replies: 65
Views: 21393

Re: new project

SANY0193.JPG SANY0194.JPG played around with the post for the softail swingarm today got it positioned where it needs to be . also measured out all the motor and trans positions made sure they were square and level and proper distances . not a lot to show but lots of time . from the rear axl to the...

Go to advanced search