Search found 1036 matches
- Fri Dec 30, 2022 10:03 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
That is one hella beefy duty notcher ya got there Curt. I like Baliegh tn250 super ridgid can cut offset and on a bend and over 180 degrees great for roll cages stupid nice for most all bike stuff but a pain to get setup going back to an even cut from an offset . i added a bolt to help and it would...
- Fri Dec 30, 2022 12:59 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
ya sucks but learned the hard way what i was doing wrong and ill keep the pieces and make something else out of them
- Thu Dec 29, 2022 4:40 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
SANY0213.JPG SANY0214.JPG SANY0215.JPG made three stupid mistakes today apparently i dont learn . first 2 i screwed the rotation on the final bend then on the replacement i put the bend on the wrong side of the line so now the 25 degree angle is to short to hit the axl in the right spot . :angry-ba...
- Tue Dec 27, 2022 10:36 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
it is dan it was easier quittin smokin
- Mon Dec 26, 2022 5:27 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
you know your having fun when you keep takin 1/16 at a time to get everything all even from side to side i love that notcher
- Fri Dec 23, 2022 11:39 am
- Forum: Project Build-Logs
- Topic: The Unholy Virgin...Reincarnate
- Replies: 109
- Views: 59066
Re: The Unholy Virgin...Reincarnate
i like the brass ones better too
- Thu Dec 22, 2022 5:55 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
i will maz . SANY0204.JPG SANY0205.JPG SANY0207.JPG had a little time today bent up the lower rails to the backbone . im not going to bend the rails up to the rear till i get the notches finalized to the backbone so that will be a little while . i never made one that went to the backbone before 3 tu...
- Mon Dec 19, 2022 9:48 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
thank you
- Sun Dec 18, 2022 6:44 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
got my garage back had some time to clean the notches and a little tack welding . got to work on the seat post tube so i can lock it in and start the bottom tubes
- Mon Dec 12, 2022 4:55 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
SANY0199.JPG SANY0198.JPG its good to be back at it but i been stuck working on the daily . took a week to get the timing chains and tensioners should have the torque to yield crank and jackshaft bolt tomorrow . what is it with having to wait for everything anymore and not just a day or so but a we...
- Thu Dec 01, 2022 8:42 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
got the bender setup and bending today notched out the wishbones took about 6 tries and a used hole saw to get them perfect . tomorrow i plan to clean up the notches and tube to tack everything together
- Wed Nov 30, 2022 10:31 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
tube showed up so i spent some time putting the 17 degree bevel on the motor and trans mounts . slow going with a rotary file and drill press but should be a nice tight fit
- Mon Nov 28, 2022 4:37 pm
- Forum: The Bull Pen
- Topic: shop talk by dennis kirk with bitter end old school chop
- Replies: 2
- Views: 3747
shop talk by dennis kirk with bitter end old school chop
https://youtu.be/_m1J5P4LhoM saw this the other day watch from the 47 min mark
- Sun Nov 27, 2022 10:27 pm
- Forum: Project Build-Logs
- Topic: The Unholy Virgin...Reincarnate
- Replies: 109
- Views: 59066
- Sat Nov 26, 2022 7:10 pm
- Forum: Frame Fabrication
- Topic: new project
- Replies: 65
- Views: 46307
Re: new project
SANY0193.JPG SANY0194.JPG played around with the post for the softail swingarm today got it positioned where it needs to be . also measured out all the motor and trans positions made sure they were square and level and proper distances . not a lot to show but lots of time . from the rear axl to the...