Page 1 of 1
Maz's Universal Wheel Truing Jig
Posted: Thu Oct 27, 2011 4:27 pm
by Maz
Just in case any of you haven't got a wheel truing jig yet and need one, here's one I made which takes rim sizes from super skinny 2.50x21 right up to 18 inches wide...
- Wheel jig 003.jpg (168.48 KiB) Viewed 9604 times
- Wheel jig 006.jpg (123.44 KiB) Viewed 9604 times
- Wheel jig 007.jpg (182.67 KiB) Viewed 9604 times
- Wheel jig Painted 02.jpg (28.93 KiB) Viewed 9604 times
As you can see from the pics, it can take wheels with and without a spindle (axle bolt) and has dual run-out pointers.....I think I did some drawings of this
I'll post them if I can find them......
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Fri Oct 28, 2011 1:29 pm
by yona
I got some leftovers from my Gotrikes bender and some 1' treadall scrounged off a constrution site...but I tend to over build anyway... ; )
Re: Maz's Universal Wheel Truing Jig
Posted: Fri Oct 28, 2011 3:33 pm
by Maz
I'm sure you'll put that to good use dude....but just in case I'll try to find the plans I drew up for the wheel truing jig.....
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Sat Oct 29, 2011 6:07 pm
by curt
ill be building one of theese i been wanting to learn to true myown rims for some time now
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 7:45 am
by Maz
you will need one of these....
- Spoke key.jpg (16.3 KiB) Viewed 9567 times
available from most good tool suppliers or evilbay.......
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 6:32 pm
by curt
i do have one of those actually never used it though
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 7:37 pm
by Maz
a guy who's never used a spoke and nipple key.....?
don't believe it
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 7:40 pm
by curt
i didnt say i didnt play with nipples now
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 8:45 pm
by Maz
curt wrote:i didnt say i didnt play with nipples now
I am very relieved to hear that
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Sun Oct 30, 2011 8:53 pm
by jonester123
Re: Maz's Universal Wheel Truing Jig
Posted: Mon Oct 31, 2011 5:00 am
by Maz
Good plan Thomas - I do have some plans I drew up for the wheel truing jig and when I can find the file I'll post it.....
Maz xx
Re: Maz's Universal Wheel Truing Jig
Posted: Thu Nov 03, 2011 5:39 pm
by curt
Re: Maz's Universal Wheel Truing Jig
Posted: Thu Nov 03, 2011 7:26 pm
by Maz
curt wrote:
oooeerrr I'm being watched again
Maz xx