Hello, Its been a long time between posts and actually having something to contribute. After some long research and viewing all of the other posts across different sites and visiting and talking to some Harley shops i have finally come up with my version.
Stats
3m long x 1m wide 75mm sides 25mm return x 4mm thick
75mm x 50mm legs
2 old trolley jack wheels
16mm scissor pivot pins
16mm rear fixed pivot pins
20mm top bearing shafts
8t Air Hydraulic ram $150
Extension leg from Caravan for Tyre vice
Pesty
Pesty's lift Table
-
- NewB
- Posts: 2
- Joined: Thu Oct 27, 2011 9:03 am
- SELF INTRODUCTION: Hello, i am a qualified Fitter Machinist with extensive CNC experience. I look for unique ideas from all sorts of areas to incorporate and innovate and build improved items. Currently building the equipment required to build my first Chopper here in Western Australia.
Pesty's lift Table
- Attachments
-
- Ram area, not happy with this setup as it wants to twist the tube towards the top, will replace with 12mm plate over a wider area to minimize force.
- PA160011.JPG (35.42 KiB) Viewed 31560 times
-
- 8t Air over Hydraulic ram $150
- PA160004.JPG (38.83 KiB) Viewed 31560 times
-
- View from other end
- PA160010.JPG (36.19 KiB) Viewed 31560 times
-
- Side view of scissor
- PA160005.JPG (35.86 KiB) Viewed 31560 times
-
- Top view with frame Jig at Rear
- PA160008.JPG (29.29 KiB) Viewed 31560 times
-
- Close up of 8t ram and fixture
- PA160007.JPG (36.19 KiB) Viewed 31560 times
- jonester123
- Builder
- Posts: 402
- Joined: Tue Oct 25, 2011 12:06 pm
- SELF INTRODUCTION: Hello guys and gals, working on my 1979 honda cb750 bobber chopper build plus many other projects etc. I have two workshops at home that i built so i can build bikes and all sorts of parts, and i mainly do auto body work and restoration repairs etc.
- Location: Armstrong B.C Canada
- Contact:
Re: Pesty's lift Table
Hello pesty, table looks real good you did a nice job building it. Should work real good for you, i made mine from heavy duty wood which makes it real heavy but works real well. I made it to the height that was best to work on it with no need to have to use any jacks or rams to raise or lower it, may not look real pretty but functional. All i need is my ramp to roll my bikes up on it and tie them down with ratchet straps.
- Maxthegardener
- Builder
- Posts: 384
- Joined: Tue Oct 25, 2011 11:28 am
- SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
- Location: Angus, Scotland
Re: Pesty's lift Table
Very nice....
- Maz
- Biker Mistress
- Posts: 714
- Joined: Tue Oct 25, 2011 4:02 pm
- SELF INTRODUCTION: The Biker Mistress, Blonde, blue eyes, English Lady bike builder and previously a member of the CBH. I run my own custom bike and chop shop (MazChopz) on the south west coast of England. I have been building custom bikes for over 35 years and have built some 130 bikes so far. I am happy to share my knowledge and "expertise" and also hope to learn from the other forum members. I look forward to meeting up with many of my friends from the CBH and especially to seeing how Dan got on with his Knuck.
- Location: South West Coast of England
- Contact:
Re: Pesty's lift Table
I like that design - I almost built mine that way but in the end went for the heavier frame type as it suited my needs better. I will have a go at building a scissor type when I do the next one. Great job dude
Maz xx
Maz xx
Blonde, blue eyes, English Custom Bike builder and Biker Mistress!!!