custom length pushrods

Like it says above.
Post Reply
User avatar
railroad bob
Contributor
Posts: 939
Joined: Fri Nov 04, 2011 10:07 pm
SELF INTRODUCTION: Hi Dan, thanks for your time and energy spent on this new board. I hope you will give me a waiver on the email account, I have used gmail so long I don't have a clue what my service provider account is.
I just returned home from a 2 week trip in New Mexico, have a few good pix, can't wait to share my off-highway traveling. Got to put 1400 miles on the scoot.

Best, Bob Davidson
Location: Alaska

custom length pushrods

Post by railroad bob »

Found this link in a DIY section, making pushrods to your custom length...

http://aircooledtech.com/custom_push_rods/

Then went to the supplier and found this,
http://www.cbperformance.com/catalog.as ... tID=1243is link...

Chromoly with dimensions. I didn't compare to HD rods. but if you don't like adjustable rods, you might give these consideration.
8 to a set for $155, enough for 2 HD evo motors. Some high performance motors are very hard on adjustable pushrods.
I know I've bent some in the past.
Alaska - Land of the Individual and Other Endangered Species
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
hansgoudzwaard
Contributor
Posts: 804
Joined: Wed Oct 26, 2011 10:43 pm
SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.

Re: custom length pushrods

Post by hansgoudzwaard »

Thanks R'Bob.

This......I can use immediately.

http://aircooledtech.com/tools-on-the-c ... ing_beads/
User avatar
Maxthegardener
Builder
Posts: 384
Joined: Tue Oct 25, 2011 11:28 am
SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
Location: Angus, Scotland

Re: custom length pushrods

Post by Maxthegardener »

andy....
User avatar
railroad bob
Contributor
Posts: 939
Joined: Fri Nov 04, 2011 10:07 pm
SELF INTRODUCTION: Hi Dan, thanks for your time and energy spent on this new board. I hope you will give me a waiver on the email account, I have used gmail so long I don't have a clue what my service provider account is.
I just returned home from a 2 week trip in New Mexico, have a few good pix, can't wait to share my off-highway traveling. Got to put 1400 miles on the scoot.

Best, Bob Davidson
Location: Alaska

Re: custom length pushrods

Post by railroad bob »

hansgoudzwaard wrote:Thanks R'Bob.

This......I can use immediately.

http://aircooledtech.com/tools-on-the-c ... ing_beads/
You might do research on this. It sounds good, but I've seen posts on the motocy forum on craigslist
that were not favorable.

The concept sounds reasonable tho.
Alaska - Land of the Individual and Other Endangered Species
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
User avatar
railroad bob
Contributor
Posts: 939
Joined: Fri Nov 04, 2011 10:07 pm
SELF INTRODUCTION: Hi Dan, thanks for your time and energy spent on this new board. I hope you will give me a waiver on the email account, I have used gmail so long I don't have a clue what my service provider account is.
I just returned home from a 2 week trip in New Mexico, have a few good pix, can't wait to share my off-highway traveling. Got to put 1400 miles on the scoot.

Best, Bob Davidson
Location: Alaska

Re: custom length pushrods

Post by railroad bob »

hansgoudzwaard wrote:Thanks R'Bob.

RRB is easier..... :lol:
Alaska - Land of the Individual and Other Endangered Species
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
Post Reply

Return to “Motors, Transmissions, & Drive Systems”