Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 8:39 pm
Next Chop
91 Ninja EX 500 R
91 Ninja EX 500 R
The Chopper Compendium
grassroots chopper building
https://choppercompendium.com/ccforum/
Busted Rubber - The Unwanted Child- Build
https://choppercompendium.com/ccforum/viewtopic.php?f=39&t=705
Page 1 of 10
Re: Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 9:02 pm
Cool man, what you plan on doing to the motorcycle.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 9:10 pm
DIGGER!
or whatever happens!
or whatever happens!
Re: Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 9:12 pm
Steel Frame
Steel Swingarm
75 horses
12 sec quarters
129 mile per hour top speed
0 to 60 3.8 sec
300$ and a chop no one else has! Watch this space!
10000 rpm revs before redline!!
Steel Swingarm
75 horses
12 sec quarters
129 mile per hour top speed
0 to 60 3.8 sec
300$ and a chop no one else has! Watch this space!
10000 rpm revs before redline!!
Re: Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 9:23 pm
Sweet good luck on build. 
Re: Busted Rubber - The Unwanted Child- Build
Posted: Thu May 22, 2014 9:27 pm
Carbs not injection and chain drive + light weight. coils no fancy ingnition. Perfect for full frame build!
Re: Busted Rubber - The Unwanted Child- Build
Posted: Fri May 23, 2014 6:13 am
Concept drawing.
Next week on Jig
Next week on Jig
Re: Busted Rubber - The Unwanted Child- Build
Posted: Fri May 23, 2014 9:33 am
Re: Busted Rubber - The Unwanted Child- Build
Posted: Fri May 23, 2014 9:54 am
Broke her down a bit and removed wiring.
Then cut the tail section off.
Then cut the tail section off.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Fri May 23, 2014 10:37 am
I like the sound of this bike .
Sounds tough. Again you don't waste time.
Nice project, I'll be following closely.
Sounds tough. Again you don't waste time.
Nice project, I'll be following closely.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Tue May 27, 2014 9:34 am
Ready to alighn and weld down.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Tue May 27, 2014 7:10 pm
Frame gone.
Need to clean up neck.
Going to reuse these axle plates perfect to build off of.
Need to clean up neck.
Going to reuse these axle plates perfect to build off of.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Tue May 27, 2014 7:38 pm
I almost forgot I picked up the materials for frame build.
36 ft 1in dom tube .120 wall
8 ft 3/4 for slugs .120 wall
1in solid bar
3/4 in solid bar
1.25 solid bar
10 ft 1/2 solid bar.
150$
36 ft 1in dom tube .120 wall
8 ft 3/4 for slugs .120 wall
1in solid bar
3/4 in solid bar
1.25 solid bar
10 ft 1/2 solid bar.
150$
Re: Busted Rubber - The Unwanted Child- Build
Posted: Wed May 28, 2014 12:51 am
What size back wheel ? Using the stock one?Customize IT wrote:
Going to reuse these axle plates perfect to build off of.
Re: Busted Rubber - The Unwanted Child- Build
Posted: Wed May 28, 2014 2:25 am
Both rims are 16in.
Going to reuse both rims and if I do it right the axles as well.
The lower tree is steel so will be able to cut the steering shaft out and weld to new tree. Just do a build up technique for the girder trees with steel this time.
Still unsure about how far I can go on rake? 45, 50, 55, 60. degrees need to figure that out?
Going to reuse both rims and if I do it right the axles as well.
The lower tree is steel so will be able to cut the steering shaft out and weld to new tree. Just do a build up technique for the girder trees with steel this time.
Still unsure about how far I can go on rake? 45, 50, 55, 60. degrees need to figure that out?