Page 3 of 8
Re: Honda Rebel 250 Springer Build
Posted: Tue Jul 21, 2015 5:10 pm
by Swamprabbit1
Axle plates fitted to the radius, Drilled and tapped for the axle adjuster bolts.
Started on the upper tube.
Re: Honda Rebel 250 Springer Build
Posted: Thu Jul 23, 2015 2:10 pm
by Swamprabbit1
Got a little more work done today at lunch.
Can you say grinning like a opossum.
Re: Honda Rebel 250 Springer Build
Posted: Sun Aug 16, 2015 1:35 am
by Swamprabbit1
Got a little work done on the cross braces this week. Almost ready to weld up the rear of the frame. All butt joints plug welded. Butt joints have been gaped to allow penetration welds into the plugs and the joining tubes.
Re: Honda Rebel 250 Springer Build
Posted: Sun Aug 16, 2015 1:36 am
by Swamprabbit1
Some changes have been made. Will be running a 21" font wheel for sure. Whit that being said. The original springer tree was built off the Rebel's factory front wheel. Since I will be running a Narrow Glide 21" front wheel with break rotor. I am able to narrow the trees up a total of 2 inches.
Here is the new springer trees Cyclopes Style but with my own design. (Cyclopes or Pogo Stick style means a single spring design) My spring perch is also incorporated into the lower tree instaed of have a mid spring perch.
Re: Honda Rebel 250 Springer Build
Posted: Sun Aug 16, 2015 12:15 pm
by hansgoudzwaard
That will be a nice springer. I did an online Cyclops image search, and some examples of a Ron Finch springer came up.
Good job.
Re: Honda Rebel 250 Springer Build
Posted: Sun Aug 16, 2015 8:59 pm
by Swamprabbit1
hansgoudzwaard wrote:That will be a nice springer. I did an online Cyclops image search, and some examples of a Ron Finch springer came up.
Good job.
Yes it will. That is my inspiration coming from. Ron is a great guy with a wide open mind.
Re: Honda Rebel 250 Springer Build
Posted: Tue Aug 25, 2015 10:01 am
by Swamprabbit1
Re: Honda Rebel 250 Springer Build
Posted: Tue Aug 25, 2015 5:28 pm
by Swamprabbit1
Re: Honda Rebel 250 Springer Build
Posted: Wed Aug 26, 2015 3:09 pm
by Swamprabbit1
Plate stacked to insure hole alignment.
4 more holes to go. Then to start cutting the outline.
Re: Honda Rebel 250 Springer Build
Posted: Tue Sep 01, 2015 2:35 pm
by Swamprabbit1
2 more holes for the inside radius.
Couple cuts made today. Starting to take shape.
Re: Honda Rebel 250 Springer Build
Posted: Tue Oct 27, 2015 3:32 pm
by Swamprabbit1
A little update. Frame welded and primered (surface rust reasons). Fitting up the curved rear support tubes. Next will focus on the neck support.
Re: Honda Rebel 250 Springer Build
Posted: Tue Oct 27, 2015 3:36 pm
by Swamprabbit1
Re: Honda Rebel 250 Springer Build
Posted: Tue Oct 27, 2015 3:38 pm
by Swamprabbit1
Re: Honda Rebel 250 Springer Build
Posted: Tue Oct 27, 2015 5:52 pm
by gearhead1951
Re: Honda Rebel 250 Springer Build
Posted: Sat Oct 31, 2015 9:50 pm
by Swamprabbit1
Neck brace cut and fitted up.
Pattern transferred to the neck brace. Next to cut out the trident.
Thanks gearhead1951.