Search found 16 matches
- Mon Aug 20, 2012 3:42 am
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Ok i'll try that.
- Sun Aug 19, 2012 5:56 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Should I remove the inner springs on both top and bottom if I'm gonna try that?
- Sun Aug 19, 2012 3:18 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Ok so the bike is almost done on mock up, meaning ready to ride around the block before being registered, then broken down for paint. So the question is since the bike is on the ground should I be able to make the front end move by putting my weight on it and pushing up and down? Because the springs...
- Sun Jul 01, 2012 3:28 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Thanks for all the compliments. I took standard measurements from online for a round oil bag, which they want an unseemly amount of money for and used those dimensions to make this one. It's a 6" round piece of copper tube 11 7/8" long. What you don't see in the pic are on the ends are goi...
- Sun Jul 01, 2012 2:22 am
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
I don't see it making much difference, using logic it doesn't seem like it would have that much affect unless your spring rods were crap. But then again it's the little things that sometimes matter.
- Sat Jun 30, 2012 6:59 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Thanks, I machined them with a corner rounding bit.
- Sat Jun 30, 2012 3:43 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
- Sat Jun 30, 2012 3:42 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Pictures here! I built and machined everything myself, motor and wheels aside.
- Fri Jun 29, 2012 1:17 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Thanks I figure the same thing, can't hurt but if your spring rods are solid you should have no problem.
- Thu Jun 28, 2012 2:19 am
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Well got the springer built.
There is a part that bolts the two spring rods together at the top, it's called the spring bridge. Is that necessary to have? I noticed most springers do not have it, but the plans from gary does. I made it, I just think it looks better without it.
There is a part that bolts the two spring rods together at the top, it's called the spring bridge. Is that necessary to have? I noticed most springers do not have it, but the plans from gary does. I made it, I just think it looks better without it.
- Mon Jun 18, 2012 8:33 pm
- Forum: Frame Fabrication
- Topic: Rear Hoop Clearances Help
- Replies: 9
- Views: 10514
Re: Rear Hoop Clearances Help
Sweet thanks. So I'll go 1/4" on the drive side and make the hoop equidistant on each side. Thanks for the help. Will post update pics once it's welded up. I also just finished my copper oil tank. I'll start a new thread for that.
- Mon Jun 18, 2012 7:20 pm
- Forum: Frame Fabrication
- Topic: Rear Hoop Clearances Help
- Replies: 9
- Views: 10514
Re: Rear Hoop Clearances Help
Ok, we all seem confused. But I appreciate the thought everyone is giving. The frame I had i built from scratch with the tires and rims that I had on hand. Then I bought some nicer rims for cheap so I'm going with those. So I chopped my new frame to account for the new rims and drive line, no biggie...
- Mon Jun 18, 2012 1:13 pm
- Forum: Frame Fabrication
- Topic: Rear Hoop Clearances Help
- Replies: 9
- Views: 10514
Re: Rear Hoop Clearances Help
Sure I'll post a pic when the chopping is done, but I need clearance dimensions first.
That still doesn't answer my question. I need to know the distance between the outer edge of the pulley and the frame so I know what inner width to make the hoops. Thanks.
That still doesn't answer my question. I need to know the distance between the outer edge of the pulley and the frame so I know what inner width to make the hoops. Thanks.
- Sun Jun 17, 2012 8:54 pm
- Forum: Frame Fabrication
- Topic: Rear Hoop Clearances Help
- Replies: 9
- Views: 10514
Rear Hoop Clearances Help
OK, so I built a custom frame and ended having to chop it to fit the wheels I got, I got a smokin' deal on some genuine harley rims. First question should I offset the rear hoop so the clearance is correct on each side of the wheel, so that the hoop is actually offset from the bike? Or should I make...
- Tue May 22, 2012 12:37 pm
- Forum: Springers, Girders, Spirders and Leafers
- Topic: Springer Welding, Need some clarification?
- Replies: 23
- Views: 9802
Re: Springer Welding, Need some clarification?
Great. Thanks.