Page 3 of 5
Re: Death By SnuSnu's Vokaro
Posted: Sun Aug 16, 2020 3:52 pm
by DeathBySnuSnu
Fuel rails roughed out. Started on the finish machine work....but a ways to go yet.
![15969865106180.jpg](./download/file.php?id=2978&sid=f8fdc918fe5879e6e18632be51837003)
- 15969865106180.jpg (26.15 KiB) Viewed 16243 times
And dug through the junk boxes and found a few parts to use.
Boards to build on and a pressure regulator and a map sensor.
![15969268871250.jpg](./download/file.php?id=2979&sid=f8fdc918fe5879e6e18632be51837003)
- 15969268871250.jpg (51.68 KiB) Viewed 16243 times
![15969865227461.jpg](./download/file.php?id=2980&sid=f8fdc918fe5879e6e18632be51837003)
- 15969865227461.jpg (32.13 KiB) Viewed 16243 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Aug 16, 2020 3:55 pm
by DeathBySnuSnu
One intake built, welded and cleaned up.
The other parts made and yet to weld.
![15976021080660.jpg](./download/file.php?id=2981&sid=f8fdc918fe5879e6e18632be51837003)
- 15976021080660.jpg (51.56 KiB) Viewed 16243 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Aug 23, 2020 4:53 pm
by DeathBySnuSnu
The whittled flywheel, Mazda pressure plate, VW type 5 disc and throw out....... All fit into the Porsche 901 bell housing.
![15981185733861.jpg](./download/file.php?id=2982&sid=f8fdc918fe5879e6e18632be51837003)
- 15981185733861.jpg (86.81 KiB) Viewed 16228 times
![15981187395283.jpg](./download/file.php?id=2983&sid=f8fdc918fe5879e6e18632be51837003)
- 15981187395283.jpg (78.95 KiB) Viewed 16228 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Aug 23, 2020 5:04 pm
by DeathBySnuSnu
Now to make an adapter to put the VW Jetta TDI starter on the Porsche 901 trans in the correct place to engage the VW type 1 ring gear.
![15982154736190.jpg](./download/file.php?id=2984&sid=f8fdc918fe5879e6e18632be51837003)
- 15982154736190.jpg (37.38 KiB) Viewed 16228 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Sep 20, 2020 5:52 pm
by DeathBySnuSnu
I did get a Jetta TDI starter adapted to the Porsche trans.
![15984879548671.jpg](./download/file.php?id=2985&sid=f8fdc918fe5879e6e18632be51837003)
- 15984879548671.jpg (64.23 KiB) Viewed 16171 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Sep 20, 2020 5:56 pm
by DeathBySnuSnu
Building chassis.....just the beginnings.
![16005384387270.jpg](./download/file.php?id=2986&sid=f8fdc918fe5879e6e18632be51837003)
- 16005384387270.jpg (54.32 KiB) Viewed 16171 times
![16005384475471.jpg](./download/file.php?id=2987&sid=f8fdc918fe5879e6e18632be51837003)
- 16005384475471.jpg (50.76 KiB) Viewed 16171 times
Re: Death By SnuSnu's Vokaro
Posted: Sun Sep 20, 2020 5:58 pm
by DeathBySnuSnu
Teaser mock up.
![15999461663372.jpg](./download/file.php?id=2988&sid=f8fdc918fe5879e6e18632be51837003)
- 15999461663372.jpg (35.48 KiB) Viewed 16171 times
![15999461560221.jpg](./download/file.php?id=2989&sid=f8fdc918fe5879e6e18632be51837003)
- 15999461560221.jpg (45.57 KiB) Viewed 16171 times
Re: Death By SnuSnu's Vokaro
Posted: Thu Dec 10, 2020 2:45 pm
by DeathBySnuSnu
Yeah.....still working on it....just no time.
I have done several small things.
Got a chevy distributor and made it fit.
Made a few mount tabs and what nots.
Painted a part or two.
Making pulleys...ect
![16054669943361.jpg](./download/file.php?id=2997&sid=f8fdc918fe5879e6e18632be51837003)
- 16054669943361.jpg (57.11 KiB) Viewed 15788 times
![16070959878540.jpg](./download/file.php?id=2998&sid=f8fdc918fe5879e6e18632be51837003)
- 16070959878540.jpg (31.41 KiB) Viewed 15788 times
Re: Death By SnuSnu's Vokaro
Posted: Thu Dec 10, 2020 2:48 pm
by DeathBySnuSnu
Painted valve covers..
![16059860881183.jpg](./download/file.php?id=2999&sid=f8fdc918fe5879e6e18632be51837003)
- 16059860881183.jpg (58.55 KiB) Viewed 15788 times
![16059861850624.jpg](./download/file.php?id=3000&sid=f8fdc918fe5879e6e18632be51837003)
- 16059861850624.jpg (74.3 KiB) Viewed 15788 times
Re: Death By SnuSnu's Vokaro
Posted: Thu Dec 10, 2020 3:00 pm
by DeathBySnuSnu
The big work such as the chassis is going slow. Just have not had the big time to spend on the big work.
I have about settled on where the body will sit and have started on the body mount perimeter.
![16054669401450.jpg](./download/file.php?id=3001&sid=f8fdc918fe5879e6e18632be51837003)
- 16054669401450.jpg (35.4 KiB) Viewed 15788 times
![16059860453022.jpg](./download/file.php?id=3002&sid=f8fdc918fe5879e6e18632be51837003)
- 16059860453022.jpg (56.16 KiB) Viewed 15788 times
![16059859145540.jpg](./download/file.php?id=3003&sid=f8fdc918fe5879e6e18632be51837003)
- 16059859145540.jpg (40.38 KiB) Viewed 15788 times
Re: Death By SnuSnu's Vokaro
Posted: Thu Dec 10, 2020 3:04 pm
by DeathBySnuSnu
Modified a set of pedals.
One inch shorter and spread out.
![16064124453591.jpg](./download/file.php?id=3004&sid=f8fdc918fe5879e6e18632be51837003)
- 16064124453591.jpg (42.76 KiB) Viewed 15788 times
![16064124154980.jpg](./download/file.php?id=3005&sid=f8fdc918fe5879e6e18632be51837003)
- 16064124154980.jpg (32.54 KiB) Viewed 15788 times
Re: Death By SnuSnu's Vokaro
Posted: Sat Feb 06, 2021 10:25 pm
by DeathBySnuSnu
Well I don't post much..... not a lot of reply/questions here.....so I don't post often.
But.
I purdy much lost all of December being sick with covid.
Then spent all of January getting caught up.
Now just plain busy.
I am trying to get back on the project.....just so much job to do.
That means I have not had big time to do the big parts.
I have gotten some poly seats and established position and roll bar height. Then started bending tube. I had a chassis kit from years gone by....but it was not for this car
I have been blocking up the body and setting weights on it for 2 months now. I have evened out some twist and miss-shape and have the body sitting better. That also means I had to un-do some of my made to fit parts.
![16112026176082.jpg](./download/file.php?id=3006&sid=f8fdc918fe5879e6e18632be51837003)
- 16112026176082.jpg (28.23 KiB) Viewed 15669 times
![16112026584933.jpg](./download/file.php?id=3007&sid=f8fdc918fe5879e6e18632be51837003)
- 16112026584933.jpg (47.1 KiB) Viewed 15669 times
![16112853423840.jpg](./download/file.php?id=3008&sid=f8fdc918fe5879e6e18632be51837003)
- 16112853423840.jpg (29.31 KiB) Viewed 15669 times
Re: Death By SnuSnu's Vokaro
Posted: Fri Mar 19, 2021 11:22 am
by budoka
this is gonna be absolutely wicked when you're done. you gonna keep it pink?
-dan
Re: Death By SnuSnu's Vokaro
Posted: Sun Mar 21, 2021 11:44 pm
by DeathBySnuSnu
Actually that is the original color still on it.
When cleaned and buffed it looks like this .
![16163851582391.jpg](./download/file.php?id=3012&sid=f8fdc918fe5879e6e18632be51837003)
- 16163851582391.jpg (44.88 KiB) Viewed 15636 times
But no..,.
I have tons of fiberglass work to do.
Just in my pics you can see I cut the tops out of the front wheel arches.....so I hafta bulge them out to fit.
Then I cut the whole back end off. As I lengthened the chassis I gotta create from scratch much of the back end. But I do have the valve covers below deck height....with the whole injection sticking out.
So..,I have a lot of body work and paint in my future.
I imagine silver and red like the old race porsches.
![16163851188720.jpg](./download/file.php?id=3013&sid=f8fdc918fe5879e6e18632be51837003)
- 16163851188720.jpg (28.71 KiB) Viewed 15636 times
Re: Death By SnuSnu's Vokaro
Posted: Mon Mar 22, 2021 9:39 am
by budoka
oh yeah, i can see that combo looking real sweet.
keep on keepin' on!
-dan